My Car
Find Parts
What's New?

Heeltoe's Recommended Brake Bedding Notes

  • Posted: 07-12-2007 12:56 PM
  • 0 Comments
  • Brakes

First it is important to know what pads you have, and what they are capable of. Heeltoe Automotive recommends Racingbrake or Hawk Racing pads, which offer different levels of performance depending on your needs. Find out more about the differences in pads under product descriptions on Heeltoeauto.com!  
 

Alert:
 
Bed in is not a one-time thing. If you overheat the brakes or use them irregularly they can "un-bed" as it were and the friction surface is not ideal. It can manifest itself with noise, glazing, shaking....you need to go out and re-bed the brakes. Sometimes you need more aggressive pads to get it done!
 
 
 
The following bed-in procedure is drawn from our personal experience in breaking in pads, and from technical information gathered from the Racingbrake Website.
 
All brake pads must be bedded-in with the rotor they will be used against. Even though those performance street pads have been burnished at the factory, a transfer film must be generated at the pad and rotor interface for optimal performance. Whether it is new or used rotors, you must follow the bed-in steps listed below to maximize brake performance.
 
STREET PADS, example Racingbrake ET300/500,  Hawk HPS, Ceramic, and HP+
 

  • After installing new brake pads, confirm pedal pressure before driving car. On an open road with no traffic, make 3-4 heavy slow-downs, NOT complete stops, from 30-10 mph then fast
    accelleration and repeat with increasing pedal effort/brake effort each time until just shy of ABS activation. The idea is to heat and maintain that heat in the pads and rotors during the
    procedure.  
  • On an open road with no traffic, make an additional 2 to 3 hard slows from approximately 45 mph to 5 mph applying firm pressure.Do not drag brakes or come to a complete stop. Engagement of ABS or threshold braking is not required but if it happens that is ok.
  • Now, gradually building heat into the brakes, I like to run up to about 80 and bring the car down to about 40 mph in a short distance with heavy pedal pressure. Do this 2-3 times. You may experience some fading if your brake fluid is not upgraded and you have stock brake lines.
  • Allow 15 minutes for brake system to cool down by cruising at normal speeds.

 

 
Do not sand or grind the brake pads or rotors after this burnishing procedure has been completed. Your performance street pads are now ready for driving! I generally recommend to drive the car normally from here on out. I do not recommend using the brakes as a way to slow the car down, but rather use them as a way to CHANGE SPEEDS to a lower one. Keeping this thought in mind while braking will prevent you from making long gradual stops that raise brake temperatures above the desired level for street pads. When street pads get too hot, they can glaze the rotor surface or put inconsistent pads deposits on the rotor which will cause a shimmy.
 
Also, be aware that Racingbrake rotors have a special metallurgy that may require up to 500 street miles before break-in is achieved. You will need to get these rotors HOT! If there are not plumes of smoke billowing from new Racingbrakes you probably did not get them hot enough.
 
Lastly, do your best not to engage the ABS system within at least 300-500 miles of bed-in. If a shimmy should develop, one should reapply the bed-in procedure listed above.
 
 
! Added 6/8/10 !
 
You will know your brakes are bedded correctly when they look smooth without much or any trace of the factory's cross hatched finish.
These Racingbrake 2-Piece rotors were returned to us because the customer was having a shimmy problem. We saw as soon as we opened the package we noticed that they had not been bedded properly. Even with ET500 pads the bedding was not aggressive enough to take down the cross hatching.

 
The same rotors as above after being bedded properly. I took the returned rotors and put them on the HT-Spec TSX. Some initial shimmy was noticed until heat was built up and pedal pressure increased. All shaking prompt went away ad has not returned in months of mixed driving. It is not the greatest image, but you can see the cross hatching is gone after one bedding session.

 
 
If you hear a noise after bedding that sounds like the brakes are dragging a little, this is relatively common. As your brakes wear in this noise will go away or at least will get very faint.
 
If you are looking at the not-bedded image above and notice that dimple in the rotor face, it is also normal. This dimple is evidence that the rotors have been hardness tested to ensure quality control. The dimple is deep an will not go away, and it does not hurt anything. If anything, be glad it is there, since no other brake companies really seem to care enough about their products to test their hardness before shipping them!

 
 
 
 
 
 
RACE PADS, example Hawk Blue or other Motorsports Pad
 
Prospective racers are cautioned that unless these racing pads are properly bedded-in at race track conditions it can result in pre-mature failure or ill effect.
 

 

  • Seal all brake ducts if any.
  • Slowly engage brakes 6 to 8 times at medium speeds (60 - 80 mph).  Do not drag brakes or come to a complete stop.
  • Increase speeds to simulate race conditions; allow 6 to 8 high pressure (about 500 psi) snubs at racing speed. Total engagements for Step 2 should be a maximum of 15 to 20.
  • Remove brake duct seals.  Allow the system to cool for about 15 minutes.  Do not engage brakes while car is parked during cool down period.

 

 
Do not sand or grind the brake pads or rotors after this burnishing procedure has been completed. Your motorsports pads are now ready for race!  
 
 
 
 
 
 
Base text sourced from Racingbrake Street Pad Beak-in and Racingbrake Motorsports Pad Break-in.

 


About the Author

Marcus di Sabella Marcus is the founder of Heeltoe Automotive. He's been working with cars (mostly Honda cars) since 1996, and has been providing enthusiasts with excellent products, services, and web experiences since 2002. He's been published in Honda Tuning, and holds a degree in Engineering Technology.
Related Items

HT-Spec Modified Maintenance Kit B, Oil/Trans/Brake Fluid Change (every 7500 miles)
HT-Spec Modified Maintenance Kit B, Oil/Trans/Brake Fluid Change (every 7500 miles)

Motul Brake Fluid DOT 5.1, .5 liter
Motul Brake Fluid DOT 5.1, .5 liter

HT-Spec Brake Package: Stage 0 Standard-Plus, 2004-08 Acura TL & TL Type-S UA6 UA7
HT-Spec Brake Package: Stage 0 Standard-Plus, 2004-08 Acura TL & TL Type-S UA6 UA7

HT-Spec Brake Package: Stage 1 Street Enhanced, 2004-08 Acura TSX CL9
HT-Spec Brake Package: Stage 1 Street Enhanced, 2004-08 Acura TSX CL9

Honda Genuine Brake and Clutch Fluid, OEM DOT3 for reliable pressure, 08798-9008
Honda Genuine Brake and Clutch Fluid, OEM DOT3 for reliable pressure, 08798-9008

Motul Brake Fluid RBF 600 .5 liter, DOT 4, 3829HL-100949
Motul Brake Fluid RBF 600 .5 liter, DOT 4, 3829HL-100949

HT-Spec Modified Maintenance Kit A, Oil Change (every 3750 miles)
HT-Spec Modified Maintenance Kit A, Oil Change (every 3750 miles)

HT-Spec Brake Package: Stage 1 Street Enhanced, 2004-08 Acura TL & TL Type-S UA6 UA7
HT-Spec Brake Package: Stage 1 Street Enhanced, 2004-08 Acura TL & TL Type-S UA6 UA7

HT-Spec Brake Package: Stage 2 Sport Package, 2004-08 Acura TSX CL9
HT-Spec Brake Package: Stage 2 Sport Package, 2004-08 Acura TSX CL9

HT-Spec Brake Package: Stage 0 Standard-Plus, 2004-08 Acura TSX CL9
HT-Spec Brake Package: Stage 0 Standard-Plus, 2004-08 Acura TSX CL9

J's Racing Brake line system SUS (all stainless) TSX, TSX, BLS-E2-SU
J's Racing Brake line system SUS (all stainless) TSX, TSX, BLS-E2-SU


0 Comments

Be the first to comment on this entry!

Leave A Comment


The ability to post urls has been disabled by the site administrator.