My Car
Find Parts
What's New?

D-Series Piston Page

  • Posted: 10-13-2006 12:57 PM
  • Engine

The Super D-Series Piston Comparo
courtesy Heeltoe Automotive
Thank you for coming to The Super D-Series Comparo. If you are like me, you like the under dog. The D-series engine has
become a sort of under dog in the Honda performance engine scene. Largely due to the installation of bigger and more powerful
B-series power plants like the B16A, GS-R, and Type-R variants, the D-series engines usually get dumped in the trash. I look forward to the day when B-series parts get disregarded in this way in favor or the K-series' popularity. But for now, the D-series is the budget bruiser out there!
I decided to catch some of these bits on the way to the trash and do a moderate street buildup on the stock D15 in my 95 CX hatchback. The first question that rose in my mind was, "What pistons should I use?" Being a Hardin Honda employee, I took it upon myself to order one of every D-series piston new from the factory for the purposes of documenting them both photo graphically and dimensionally.
The different pistons are called out by the center 3 digits in their part numbers.
These are the numbers Honda uses to classify which engine the part goes in when determining part numbers. The second set of 3 digits I include give information as to what market the parts are from, and super-cession level. An A00 is a North American part while a 000 would be a World Market part. Likewise, a 010 might be a part superseding a 000. Compression height was calculated by measuring the distance from the TOP of the wrist pin hole to the TOP of the piston (not including any dome or dish) then adding half the wrist pin diameter. Further details regarding measurements will be at the bottom of the page. Without further ado, here are the pistons:
(I am assuming P03 and PM3 are the same since a PM3 came in a P03 box)
88-91 DX/LX, 92-95 CX/DX
total height: 61.76mm
compression height: 30.70mm
flat top

92-95 VX
total height: 57.65mm
compression height: 27.75mm
7.05mm dish

91-99 JDM Civic VTi
total height: 57.65mm
compression height: 27.4mm
1.78mm dish

>>Click to purchase<<
92-95 EX/Si
total height: 60.00mm
compression height: 30.00mm
3.00mm dish

88-89 Integra
Blacktop D16A3
total height: 58.80mm
compression height: 29.06mm
3.30mm dome

>>Click to purchase<<
92-00 CX/DX
total height: 50.00mm
compression height: 30.00mm
3.32mm dish

96-00 HX
total height: 49.26mm
compression height: 29.50mm
2.70mm dish

96-00 EX
total height: 49.25mm
compression height: 29.50mm
2.12mm dish

98-00 GX
total height: 49.28mm
compression height: 30.50mm
2.50mm dome

86-87 Integra
Browntop D16A1
total height: 59.80mm
compression height: 30.17mm
.889mm dome

>>Click to purchase<<
01-03 DX
total height: 46.50mm
compression height: 27.00mm
2.62mm dish

01-03 EX/HX
total height: 46.50mm
compression height: 27.00mm
2.66mm dish

01-03 GX
total height: 47.42mm
compression height: 27.00mm
1.50mm dome


Here are a few things I found while measuring:
:Bore diameter was the same for all pistons : 74.5 mm (I tested std bore pistons)
:Wristpin diameter was the same for all pistons at 19 mm except the PDN which has a wristpin diameter of 21 mm.
:All wristpins were the same length at 56 mm.
Well, here it is so far...I still need to get a hold of a couple more pistons, and a couple pics of the pistons above got lost, so I will need to continue where I left off here. Oh, and before you start giving me a hard time about it, I know some of my measurements are off. The Compression height was easily the hardest dimension to get right. These measurements were meant to serve comparative purposes only. Similar measurements between pistons can probably be assumed to be equal. The conditions under which I conducted the measurements were not ideal. If nothing else, you should be able to get an idea of what you can run in your buildup. Stay tuned!
Hey, check it out! I found a neat Compression Ratio calculator! Kinda fun....Chick here for the calculator!
There is another one here that we use a lot: Click here for the c-speed calculator!
A word about rods:
All D-series engines of similar displacement have equal stroke lengths. Thus, the rod lengths are the same if the displacement is the same, with one exception. The VX rod is longer that the other 1.5L engines, approximately the same as the D16 engines. The D17 engines would have longer rods still, about 3mm longer than a D16 rod.
Here is a list of what I know so far:
: 88-95 DX/LX/CX all use a PM3 rod (134mm)
: 88-00 D16 motors use the same length rods, PM6 (137mm). The D16Z6 uses a PG6 rod and the D16Y5 (HX) uses a PE1, but they both superseed to PM6 rods. The only two rods that do not superseed from a PM6 is the P2P (D16Y8) and the PDN (GX motor).
: The VX rod is comparable to a 1.6L rod in length. The number for the VX rod is P07.
: D17A rods are 137mm. Compression height is lower than 1.6 pistons ~3mm, deck height is similar from D16 to D17, and bore is equal. The D17A gets it's displacement from stroke.
: 1.7L rods are the same from DX to EX (PLM). They are the same 137mm length as the D16 rods, share the same 19mm wrist pin diameter, have the same 45mm rod journal diameter, but have a 19.8mm wide big end, unlike the D16 BE width of 22.6mm. The GX rod has a different number (PMS) but I believe it to be the same length as the PLM.
For fun:
Some pot-smokers that were making fun of me taking all these pics and measurement.

My Measuring instrument:

Copyright © 2002 -  HEELTOE Automotive

About the Author

Marcus di Sabella Marcus is the founder of Heeltoe Automotive. He's been working with cars (mostly Honda cars) since 1996, and has been providing enthusiasts with excellent products, services, and web experiences since 2002. He's been published in Honda Tuning, and holds a degree in Engineering Technology.


Fernando Duron
04-19-2015 11:53 PM at 11:53 PM
I need to buy 2 piston kit pdn where I can purchase either as buy ?
Administrator Note:
We do not have access to this part at the time being. Sorry, we don;t have a referral on where to get them.
01-03-2015 03:36 AM at 3:36 AM
Where did you get the PMS pistons. I have been searching for them with no luck. Do you have a set?

[mrheeltoe]: This article was written around 2001. We had access to all these pistons then, but many are no longer available.
Travis Edd
07-25-2012 11:55 PM at 11:55 PM
Thank you very much for this info, and keep adding to it if you can :-)

Leave A Comment

The ability to post urls has been disabled by the site administrator.