Heeltoe has been offering the Ultra Racing braces for a while, and due to the comprehensive suite of braces available for the 1g TSX/CL9 chassis we had a customer that took the plunge and bought them all. This article outlines impressions and installation for 04-08 Acura TSX models, however, bracing for other Honda/Acura models have similar fitments and benefits.
Driving Impressions Before Install
I drove the car before and after install. The suspension was Tein FLEX (which rode remarkably well as a matter of fact…this kit is NOT hands-off for street performance drivers!). The car handled reasonably well before, but the owner was complaining the car was too soft, and I felt what he was talking about. The FLEX is firm yet is tuned well for the street. For some performance drivers stating they really want a firm ride, I’d say they are not going to be firm enough.
For lack of a better suspension option to firm things up, we recommended bracing out the car. It just so happened the Ultra Racing bars we ordered just before this meeting had come in, so we did a test fitting. The hope was that we would keep the suspension more rigid and add a significant amount of feel to the car. We hoped the chassis would tighten up and allow the suspension to do it’s job better. We wanted to eliminate the springing effect the weak chassis was injecting into the car’s ride and handling.
First Impressions of the Product
First off, the staff at Ultra Racing are nice and attentive to our requests. We look hard for such qualities in our vendors because being able to communicate well with them directly impacts the service we can give to our customers! The first major reason to pursue sales with them is their great initial service.
Now, THE BARS.
The bars offered by Ultra Racing fit well and work great. We give the product a high ranking on these points.
We found overall finish quality to be certainly acceptable but hampered by lack of detail refinement and unconvincing durability on the painted finish. However, product labeling was quite good and clear. There is a definite pride in the branding. It could just be that since these bars are made in Malaysia they could benefit from higher-end manufacturing practices. That being said, we were more than happy and confident to install the bars to see how they’d work, and were not deterred or depressed at all by the finished-product observations.
Should you benefit from these parts, we’d encourage you not to be either. These observations were made only in comparison with arguably overpriced masterpieces from Japan. For parts that will essentially get destroyed under the car, we felt better installing these than Carbing museum pieces.
Before we get to the pics:
* We did not get a chance to install the fender braces¬†because of a lack of time. Unlike the J’s braces, these will require removal of the fenders to install properly. We did line them up and they will fit. We also like the welded-up construction versus the J’s braces. We anticipate these braces to offer more in the way of rigidity, especially when considering torsional forces that could act on this area of the car.
* For some reason I forgot to take some pictures of the Front Lower Arm Brace installed.¬†This is a 2-point brace, fitting in the same location as the Cusco Type-1 brace. It appeared to us that this brace offered good exhaust clearance
* There are two small bars¬†(Front Outer Frame Braces) that come in a pair that don’t fit in conjunction with the Side Lower Floor Bars. We certainly expected to see the greatest improvement in the Floor Bars so we installed these instead of the Outer Frame Braces.
* Ground Clearance¬†LOOKS to be severely hampered however the effect is not nearly as bad as you’d think. The side braces don’t hang any lower than the exhaust does, and the rear brace spans between the rear wheels. Speed bumps are not a problem, generally speaking. But cars lowered more than 2″ will have some contact with the ground from time to time. We do want to note that the customer we tested these bars with told us he had a very gnarly driveway entrance that we did scrape on and thus needed to raise his car. We did see evidence of grounding out. The concern was that as quick as these bars went on they’d need to come off because of ground clearance issues. —- The customer did have some rubbing on the ground but it was not that much and they are keeping the bars on. The reason the rubbing is not bad is simple: These bars keep the car straight and rigid over bumps and dips. The chassis flexes enough to bow the car when large bumps are encountered. These braces prevent the bowing and actually helps the suspension work the car over the bumps better! So while these bars do hang lower than the car, we’d encourage people to try them out ¬†anyway.
Driving Impressions After
After installing the bars and pulling out the driveway, we could feel a difference right away. You can actually feel the suspension articulating over dips and bumps at slow speeds. The steering felt a little lighter and more responsive. I’d speculate that the steering felt lighter because the power rack was able to move the tie-rods better without power being lost in chassis deflection. It makes me want to revise the steering rack mounts better actually!
Once we pulled out onto the street you could certainly feel the car was more rigid. It reminded me of my M3. We took a couple turns at a reasonable pace and I can say without a doubt the car was more confident feeling and certainly more capable. People with less experience tuning have a hard time grasping the benefits of bracing because it seems so obscure. Bracing adds a certain¬†je ne sais quoi¬†to the driving experience that just makes it more fun! A major reason why European cars drive so much better than Japanese ones is that they come from the factory like this!
Combine bracing, mild suspension like the ones we offer on¬†www.heeltoeauto.com,¬†or even the A-spec kit, and a rear sway bar, and you are going to have an FWD street warrior! The braces really show off how good the TSX platform is!